In the Groove Slot car Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 2 of 2      Prev   1   2
expressemery

Avatar / Picture

Administrator
Registered:
Posts: 143
Reply with quote  #16 
MEGA G+ and MAGNA-TRACTION RULES

Attached Images
jpeg 20181015_102548.jpg (2.52 MB, 3 views)
jpeg 20181009_185104.jpg (3.35 MB, 3 views)

0
expressemery

Avatar / Picture

Administrator
Registered:
Posts: 143
Reply with quote  #17 

WMHORA will have a five race season I am following the format of the MIDWEST series in hopes to attract a good turnout. Schedule will be on off dates of the MIDWEST series HOCWNN and MISCAR. Proposed classes will be G-jet HARDBODY

MAGNA-TRACTION

IROC MEGA G+

Track will be open at noon and racing will start at 2:00

15.00 entry fee will get you in all races with dinner before the IROC event.

0
expressemery

Avatar / Picture

Administrator
Registered:
Posts: 143
Reply with quote  #18 
G-Jet® Car Class Rules

1)

Cars eligible to compete in this class include the BSRT G-Jet® and Formula G-Jet®.
2)The chassis must be a stock BSRT G3-R® Flexible chassis with Flexible traction weight clip. The front axle holes may be reamed to .052”. Stock body tube holes that have been previously threaded are allowed. No other modifications are allowed.
3)Motor magnets must be BSRT #290 G-Force™ C4 Ceramic-Grade and cannot be modified.
Magnets must remain in stock position.
4)Armature must be a stock BSRT G-Jet®, narrow gap design, and be a minimum of 9-ohms.
BSRT G-Jet® 9-ohm Hot Stock™ armature may be substituted for the stock unit.
5)Armature bushings must be stock or BSRT stock replacement (no ball bearings).
Bushings may be reamed, chamfered, and polished.
6)All electrical system parts must be stock or BSRT stock replacement.
Twisted brush endbells are not allowed.
7)G-Jet® Front End: front axle and non-independent G-Jet® #878 rims and O-ring front tires must be stock and unmodified. Front O- rings must be a minimum tire diameter of .350”. In G-Jet®, front axle assembly must be installed using the short wheelbase location.
Formula G-Jet® Front End: front axle and non-independent Formula G-Jet® #877 rims and #950 front tires must be stock and unmodified. In Formula G-Jet®, front axle assembly must be installed using the long wheelbase location.
8)Rear tires must be BSRT HPS™ Injection-Molded Silicone slip-on tires on BSRT HPS™ Double-Flange Rear Rims. The rear axle must be stock or BSRT stock replacement. Front and rear rims cannot be modified. The rear axle must be stock or BSRT stock replacement. Front and rear rims cannot be modified.
9)BSRT G-Jet® handling weights must be used. Weights must be used in their stock location. Weights may not be modified.
10)Gears must be stock or BSRT stock replacement. Gears may not be lightened. Axle spacers may be used to aid with gear mesh.
11)The guide pin must be stock or BSRT stock replacement in the stock position.
12)Glues/adhesives are not allowed on the chassis except to retain the guide pin.
13)The body in Formula G-Jet® must be a Tomy snap in place stock Formula injection-molded body. The weight of the body may not be less than 2.1 grams. All wings must be secured to the body. The front wings may be repaired/reinforced using styrene by removing a small amount of plastic under the front wing. A very small amount of plastic may be removed on the body nose to allow for clearance of the front Formula G-Jet weight. Rear adjustable wing flap must be glued into fixed position. All bodies must be painted.
14)G-Jet® races shall be run at 12.0 volts +/- .25 volts.
0
expressemery

Avatar / Picture

Administrator
Registered:
Posts: 143
Reply with quote  #19 
WMHORA EVENT FLYER.jpeg 
0
expressemery

Avatar / Picture

Administrator
Registered:
Posts: 143
Reply with quote  #20 
TRACK OPEN THIS SATURDAY UNTIL 3PM
PARTS BOARD IS STOCKED FOR THE SEASON
0
expressemery

Avatar / Picture

Administrator
Registered:
Posts: 143
Reply with quote  #21 
BSRT and Viper AFX Wizzard

Attached Images
jpeg 20190920_174804.jpg (242.27 KB, 1 views)
jpeg FB_IMG_1570036539018.jpg (62.61 KB, 1 views)
jpeg Screenshot_20190914-180203_Messenger.jpg (63.31 KB, 1 views)

0
expressemery

Avatar / Picture

Administrator
Registered:
Posts: 143
Reply with quote  #22 
66475170_2373412352916632_2802679573269970944_n.jpg
0
Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.